Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
projects:kuka_lwr [2010/05/10 15:21] – clarifications kresseprojects:kuka_lwr [2013/02/12 13:58] (current) – added some new info on newer FRI versions kresse
Line 1: Line 1:
 +====== Information about the KUKA lightweight robot ======
  
 +Here we collect some bits and pieces about the KUKA lightweight robot. We hope it is useful for someone.
 +
 +===== 3D Model of the lightweight arm =====
 +
 +{{:projects:lwr.png?200 |light weight robot}}
 +
 +{{:projects:lwr-arm.blend|This}} is a blender model of the lightweight arm using subdivision surfaces. The number of vertices/faces can still be adjusted when generating meshes. It is licensed under CC-BY-3.0. 
 +
 +===== Mounting adaptors =====
 +
 +{{:projects:kuka-flanche-adaptor.png?200 |flanche adaptor model}}
 +
 +We got some really nice adapters for the hands. Here are the original {{:projects:effector_flange.zip|Solidworks files}}, some {{:projects:effector_flange_vrml.zip|VRML meshes}}, a {{:projects:effector_flange.pdf|blueprint drawing}} and the {{:projects:effector_flange_inertia.txt|mass / inertia properties}}.
 +
 +===== FRI - the Fast Research Interface for the KUKA lightweight robot =====
 +
 +The 19" KUKA control box, which is shipped with most KUKA lightweight robot arms runs actually
 +two operating systems: A Windows XP embedded which runs the GUI and a VxWorks which runs as a Windows driver and does the realtime control part.
 +
 +With the FRI component, you have an extra Intel Ethernet card which is "taken over" by the VxWorks kernel. So now there are two network cards: The embedded network card which we use for a SMB share and the realtime Intel card which we use for realtime control. To this network card we connect our "remote control computer".
 +
 +===== FRI - YARP / ROS bridge =====
 +
 +{{:projects:fri-yarp.tar.gz|This}} is the (now outdated) program that we use in our lab to connect the lightweight robot to [[http://eris.liralab.it/yarpdoc/index.html|YARP]]. The program ''fri-yarp'' runs one of our PC's which is connected to the realtime ethernet card of the KUKA control box. The program ''FRI_CONTROL.SRC'' is written in KRL and runs on the robot controller in automatic mode. You need to adjust the lines that say "CHANGEME" before using it.
 +
 +The program starts a high-priority thread for which it needs sudo permissions (Or some special POSIX permissions). It runs okayish on a stock Debian kernel, but a custom kernel which was compiled with realtime in mind is definitely better.
 +
 +We have refactored this program to be a YARP/ROS multiclient, which also publishes diagnostics and joint states to ROS. This program is in the ''kuka_fri'' package inside the public TUM-ROS repository which can be checked out with:
 +
 +  svn co https://svn.code.sf.net/p/tum-ros-pkg/code tum-ros-pkg
 +
 +In addition, the program communicates with the robot controller to switch between monitor mode and command mode (this needs a special KRL program running on the robot - see below). This KRL program is also stored in the above repository.
 +
 +The package ''kuka_fri'' requires the package ''kuka_fri_header'', which merely consists of the FRI header file that came on your FRI CD (probably ''fri_remotesample/fri_remote/fricomm.h'') and a ''manifest.xml'' file:
 +
 +  <package>
 +    <description brief="kuka_fri_header">
 +      This is the header file for the Fast Research Interface (FRI) for
 +      the KUKA lightweight robot. It is shipped with the interface
 +      binaries for the KUKA control box.
 +      
 +      Please do not distribute this file!
 +    </description>
 +    <author>KUKA Roboter GmbH</author>
 +    <license>Proprietary</license>
 +    <review status="unreviewed" notes=""/>
 +    <export>
 +      <cpp cflags="-I${prefix}"/>
 +    </export>
 +  </package>
 +
 +We are asked not to distribute this header file so this package is unfortunately not public.
 +===== KRL programming tricks =====
 +
 +The following bits and pieces were collected while writing a suitable KRL program for
 +using our lightweight arms with FRI. All these programs are executed on the Kuka control box. {{https://tum-ros-pkg.svn.sourceforge.net/svnroot/tum-ros-pkg/drivers/kuka_fri/scripts/fri_hand.src|This}} is our main KRL program and {{https://tum-ros-pkg.svn.sourceforge.net/svnroot/tum-ros-pkg/drivers/kuka_fri/scripts/sps.sub|this}} is the background program that runs in the so-called submit interpreter.
 +
 +
 +==== FRI and KRL Movements ====
 +
 +FRI is a low-level interface that lets you monitor and take control over the robot 
 +at a frequency of up to 1kHz. It runs completely in parallel to the KRL programs.
 +This has a few implications:
 +
 +  * The KRL program maintains it's own commanded position of the arm. When in command mode, FRI adds an "offset" to this KRL-commanded position. This offset is visible for KRL programs (i.e. ''$POS_ACT'' and ''$AXIS_ACT'' changes).
 +  * When switching back to monitor mode, KRL tries to go back to the KRL-commanded-position - usually, where it was at the beginning of the program. This can lead to **dangerous movements**!
 +  * If the switch back to monitor mode is due to an error message, then this movement happens before the program continues with the next instruction.
 +
 +One way to avoid this situation is to constantly adapt the KRL position to the actual position while FRI is in command mode. Another way is to reset the program if a dangerous movement would occur otherwise.
 +
 +
 +==== Sending Commands from FRI to KRL ====
 +
 +There are a few things that cannot be accomplished using only FRI:
 +
 +  * Change control strategy (position, joint impedance, cartesian impedance, ...)
 +  * Switch between Monitor and Command mode
 +  * Change control rate
 +  * Set a tool (load data)
 +
 +For this kind of commands there are some general purpose fields, both in the FRI measurement and command packets:
 +''krl.realData[]'', ''krl.intData[]'' and ''krl.boolData'' which are mapped to the KRL variables
 +''$KRL_*_REAL[]'', ''$KRL_*_INT[]'' and ''$KRL_*_BOOL[]''. The ''*'' can be either ''FRM'' or ''TO'' depending on
 +whether the variables are sent to the controlling PC or were received from it.
 +
 +For catching such a command in a KRL program there are several possibilities:
 +
 +  * setting an interrupt on a rising edge of a flag in ''$KRL_FRM_BOOL[]''.
 +  * waiting for a rising edge in one of the the FRI flags: ''WAIT FOR $FRI_FRM_BOOL[...]''
 +  * doing busy waiting on one of the FRI variables.
 +
 +We used interrupts before but when we leave command mode, we must set the
 +KRL pose to the current pose. This cannot be done in an interrupt program:
 +An interrupt program //must// return the robot to the same position where
 +it was when the interrupt started. That's why we use the wait strategy.
 +
 +This type of command sending is asynchronous, so it might be a good idea if:
 +  * The KRL program sets a "busy" flag, as long as it is processing a command.
 +  * The remote PC does not send any new command while KRL is busy.
 +  * The busy flag is set for at least one cycle, so it can serve as a confirmation.
 +An extended version of this handshake could be a running command ID, which is sent
 +by the remote PC and mirrored by KRL as long as the command is being processed.
 +
 +==== Two hours time limit ====
 +
 +After two hours of no KRL command, the robot stops the motors and hits the
 +brakes. So, every 30 minutes we command the robot to it's current position. (It
 +effectively does nothing). The only problem: When the robot is pushed to a limit
 +in that moment, then the robot stops: It is over the soft joint limits and tries
 +to set KRL to go to that pose. So this pose must be checked against joint limits
 +and corrected if necessary. The following KRL function does this:
 +
 +<code>
 +DEFFCT E6AXIS CLAMP_AXES(ax:IN)
 +E6AXIS ax
 +DECL E6AXIS an
 +
 +an.A1 = CLAMP(ax.A1, -169., 169.)
 +an.A2 = CLAMP(ax.A2,  -29., 209.)
 +an.E1 = CLAMP(ax.E1, -169., 169.)
 +an.A3 = CLAMP(ax.A3, -119., 119.)
 +an.A4 = CLAMP(ax.A4, -169., 169.)
 +an.A5 = CLAMP(ax.A5, -119., 119.)
 +an.A6 = CLAMP(ax.A6, -169., 169.)
 +
 +RETURN an
 +ENDFCT
 +
 +
 +DEFFCT REAL CLAMP(v:IN, minval:IN, maxval:IN)
 +REAL v, minval, maxval
 +DECL REAL r
 +
 +r = v
 +
 +IF v > maxval THEN
 +  r = maxval
 +ENDIF
 +
 +IF v < minval THEN
 +    r = minval
 +ENDIF
 +
 +RETURN r
 +ENDFCT
 +</code>
 +
 +==== Setting load data ====
 +
 +We usually have a 2kg hand attached to our arms. We have made a tool with appropriate load 
 +data which we can set in several ways:
 +
 +  - Using the menu: ''Configure <nowiki>--></nowiki> 6 Set tool/base''
 +  - In a program, using<code>
 +BAS(#TOOL,{tool number})
 +</code> After this line, the arm "behaved" but the message "480 LR Validate Loaddata FT 6" did not go away and FRISTART stopped the robot later.
 +  - By editing the config file ''/R1/Mada/$robocor.dat'' and changing the variables ''$DEF_L_M'' for the mass in kg and ''$DEF_L_CM'' for the center of gravity in mm and degrees. With this method, the robot boots with the suitable load data. 
 +
 +-----
 +
 +==== Getting Automatic external running ====
 +
 +We recently tried to reduce the amount of button presses that are necessary to
 +run the robot. Using the mode "automatic external", which was meant to give a PLC
 +control over the robot, it is //almost// possible to automate the teach pendant
 +interactions.
 +
 +A PLC uses digital I/O lines to send a program number to the Kuka control box,
 +enable motors, confirm messages and start the program.
 +
 +Some I/O lines can be set to ''$IN[1025]'' which is "hardwired" to ''TRUE''. Three
 +other lines must be pulsed:
 +
 +  * ''$DRIVES_ON'': Switch on motors
 +  * ''$CONF_MESS'': Confirm messages
 +  * ''$EXT_START'': Start the program
 +
 +The LWR has a [[http://www.roboterforum.de/roboter-forum/kuka_roboter/roboterantriebe_mit_driveson_einschalten-t4615.0.html|limitation]]
 +here: Switching on the motors by an external signal requires extra wiring (please ask your contact at KUKA for more information). The best thing one can achieve without this wiring is to have one press of the //ON// button when starting or re-starting after an error.
 +
 +To achieve this, we loop back some output lines to some input lines, so the Kuka control box can control "itself".
 +Then we simulate a simple PLC inside the background program SPS.SUB.
 +
 +=== Wiring back I/O lines ===
 +
 +There used to be a capability called IOSIM to simulate inputs and outputs. This has been
 +[[http://www.roboterforum.de/roboter-forum/kuka_roboter/belegung_der_leertasten_am_kcp-t4772.0.html|disabled]]
 +in newer version of the Kuka control software. A second option is an I/O driver called "O2I".
 +To enable this driver, do the following changes in ''C:\KRC\ROBOTER\INIT\iosys.ini'':
 +
 +  * To Section [DRIVERS] add the line:<code>
 +O2I=31,o2iInit,o2i_drv.o
 +</code>
 +  * In Section [O2I] uncomment the two lines:<code>
 +INW6=2       ;$IN[49-64]
 +OUTW6=2      ;$OUT[49-64]
 +</code>
 +
 +These changes require a restart.
 +
 +**Update**: As of KRC 5.3.2 build 28, the O2I driver got removed. However, the old driver still seems to work in the new version.
 +
 +=== Configuring Automatic external ===
 +
 +As expert user do
 +
 +"Monitor" -> "0 I/O" -> "3 Automatic external".
 +
 +{{:projects:kuka_lwr:aut-ext-open.png?direct|}}
 +
 +You should see the default port mappings:
 +
 +{{:projects:kuka_lwr:aut-ext-orig.png?direct|}}
 +
 +Do the following mappings:
 +
 +{{:projects:kuka_lwr:aut-ext-modified.png?direct|}}
 +
 +  $DRIVES_ON -> 49
 +  $CONF_MESS -> 50
 +  $EXT_START -> 51
 +
 +These mappings are stored in ''KRC\steu\Mada\$machine.dat''.
 +
 +These inputs need to get pulsed by the submit program. Also, set
 +
 +  $MOVE_ENABLED -> 1025
 +
 +For the last change to work, set ''$CHCK_MOVENA'' to ''FALSE'' in
 +''C:\KRC\Roboter\KRC\Steu\MaDa\OPTION.DAT''.
 +
 +=== Writing a suitable SPS.SUB ===
 +
 +{{https://tum-ros-pkg.svn.sourceforge.net/svnroot/tum-ros-pkg/drivers/kuka_fri/scripts/sps.sub|This}} is our version of the ''SPS.SUB'' background program.
 +
 +''SPS.SUB'' is run in the background by the "Submit Interpreter". It is run
 +in parallel to the main program. Some restrictions apply and certain variables
 +are write protected. These are some bits and pieces that may be useful.
 +
 +''SPS.SUB'' is responsible for starting CELL.SRC when in automatic external mode; CELL.SRC,
 +in turn, reads the I/O lines and calls the correct program. However, with some
 +modifications, CELL.SRC is no longer needed. We can start our FRI control program directly.
 +
 +**Confirming Messages**: This is a snippet for confirming messages:
 +
 +  INT M
 +  DECL STOPMESS MLD
 +  IF $STOPMESS AND $EXT THEN      ;If there is a stop message in auto external mode
 +     M=MBX_REC($STOPMB_ID,MLD)    ;Read current state in MLD
 +     IF M==0 THEN                 ;Check if we are allowed to confirm
 +        IF ((MLD.GRO==2) AND (MLD.STATE==1)) THEN
 +           CONFIRM MLD.CONFNO     ;Confirm this message
 +         ENDIF
 +     ENDIF
 +  ENDIF
 +
 +When omitting the check ''MLD.STATE==1'' then almost every message gets confirmed.
 +In this application this makes sense after the //ON// button was pressed.
 +
 +**Controlling the program state**: By writing commands to the ''$CMD'' stream one can start, stop or reset
 +KRL programs:
 +
 +  CWRITE($CMD,STAT,MODE,"RUN /R1/FRI_CONTROL()")
 +  CWRITE($CMD,STAT,MODE,"STOP 1")
 +  CWRITE($CMD,STAT,MODE,"RESET 1")
 +
 +**Some variables**:
 +
 +  * ''$MODE_OP'': One of ''#EX'', ''#AUT'', ''#T1'', ''#T2''. The current robot mode.
 +  * ''$EXT'': robot mode is "Automatic external". This is a bit more compact than ''($MODE_OP==#EX)''. Similar variables are ''$T1'', ''$T2'' and ''$AUT''.
 +  * ''$PRO_STATE1'':
 +    * ''#P_RESET'': The program was reset
 +    * ''#P_FREE'': No program selected
 +    * ''#P_ACTIVE'': Program is running
 +    * ''#P_STOP'': Program is stopped
 +
 +  * ''$PERI_RDY'': Drives are ready
 +  * ''$STOPMESS'': A stop message is being displayed
 +  * ''$PRO_ACT'':  A program is running
 +
 +The following variable is not supported with FRI 1.0.0, but has been used by others:
 +
 +  * ''$FRISTATE'': Can be ''#MON'' or ''#CMD''
 +
 +=== IO-lines on the Kuka-C2 controllers ===
 +
 +The KRC that ships with the lightweight arms has no physical input or output lines. You have to attach some IO-module using an industrial bus. However, there is a (pretty hackish) way to get some slow IO-lines with only a few wires and some code:
 +
 +From KRL it is possible to control the serial port COM3 and send (and receive) some command characters (using the CWRITE and CREAD commands). Then you connect COM3 to COM2 (which is controlled by the windows side) These commands are interpreted by a windows program which runs on the KRC in the background (find the source {{:projects:winserial.zip|here}}). This program can set the handshake pins on the serial port or control the parallel port. See the wiring diagram below:
 +
 +<code>
 +             ______________________
 +         ___/________________      \
 +       _/___|________________\_    |
 +      / |   |                | \   |
 +      | |   |                | |   |
 +      | |  _|_____           | |   |
 +   RxD| | / |     \       RxD| |   |
 +     TxD| | +---\ |         TxD|   |GND
 +  ____|_|_|_|__ | |      ____|_|___|__
 +  \ 1 2 3 4 5 / | |      \ 1 2 3 4 5 /
 +   \ 6 7 8 9 /  | |       \ 6 7 8 9 /
 +    ---------   | |        ---------
 +       COM2     | |          COM3
 +                | |
 +             GND| |DTR
 +                | |
 +
 +               OUTPUT
 +
 +</code>
 +
 +The serial port should provide two outputs and two inputs (+-12V). The parallel port has some more...
 +
 +
 +===== Other things to know =====
 +
 +  - The second joint (J2/A2) is at 90 degrees when it is completely stretched. This is due to some convention of Kuka. However, the FRI interface does //not// have this offset. With FRI, all joint limits are symmetric (i.e. J2 is zero when stretched). This suits us well, we would have removed this offset in our driver, anyway.
 +  - When the variance of the estimated force (''$TORQUE_TCP_EST'') is bigger than around 10-15, then the arm is in a singular pose and the estimated forces should not be trusted.
 +  - The message "483 - LR - Computation of Cartesian Deviation impossible" can be overcome by switching back to position control. This requirement is reportedly gone in the newest version of FRI.
 +
 +===== Glossary =====
 +
 +  * KCP: KUKA control panel
 +  * KRC: KUKA robot controller (control box)
 +  * KRL: KUKA robot language
 +  * RSI: remote sensor interface (older)
 +  * FRI: fast research interface (newer)
 +  * RDW: resolver-digital-wandler
 
Recent changes RSS feed Powered by PHP Valid XHTML 1.0 Valid CSS Driven by DokuWiki